• Familiar with the application of Completion Management System for the control of Pre-Commissioning activities• Familiar with the concept of Commissioning Systems and the representation of the same using Limits of System Handover Documents.• Ensure that the instrument and control content of the dossiers is accurate and complete before they are accepted from construction and before they are submitted to operations department.• Coordinate with operations and attend all instrument call for calibration and lining up instruments during flow circulation.• Conduct tool box talk before activity initiated.• Responsible for all instrument commissioning and line up of all instrument before start up and normal operation.• Involved in hands on testing of all types of Field instrumentation including Temperature, Ultrasonic Flow, Vortex, Level and Pressure Transmitters and calibration of vibration probes, speed probes, etc.• Experienced in the interpretation of all engineering documents including datasheets, P&IDs, Cause & Effect Diagrams, Loop Drawings, etc.

Experienced E&I Field Service Engineer for GE Oil & Gas Nuovo Pignone in installation, pre-commissioning, commissioning and start-up of PGT25 + G4 DLE gas turbine, MCL 805 single stage centrifugal compressor and 2BCL506 two stage centrifugal compressor as a vendor. Responsible in the completion and attending to outstanding E&I construction, pre-commissioning and commissioning start-up issues; together with client and coordinate with different respective disciplines. Raising Service Request (either Material or Technical) to solve different problems encountered at site that requires technical queries or procurement of materials. Assist client and performs Pre-commissioning loop checks, functional testing, dynamic functional testing, and Audit procedures. Performs hands-on E&I activities such as installations, re-wiring, calibrations, re-ranging, zero trimming, loop check, functional checks, power-ups, troubleshooting and fault finding.

Plan daily electrical activities based on priority schedule. Supervise the overall engineering installation of electrical and instrumentation system and other related works for Island D. Monitor electrical and instrumentation activities and prepare daily progress report. Review project plans, contracts, specifications and standard. Monitor and set project quality standards and requirements for scope of works along with schedules and verify that the area of responsibility is complete, accurate and conforms to established project requirements, plans and specifications. Perform estimates on electrical and instrumentation package based on bid documents, bid drawings, contracts, applicable codes and specifications, rules and standards. Take off materials. Coordinate with purchasing. Plan project execution and resources. Prepare comprehensive submittals of proposed materials and equipment for approval. Conduct surveillance checks in determining the soundness of Issued for Construction drawings and raise site technical queries encountered which requires disposition/clarification from client. Coordinate with electrical supervisors and provide technical information on project implementation.Execute site work related on Electrical, Instrumentation and Telecommunication (E&IT) and conduct inspection as per work pack. Conduct walk down /survey and prepare spreadsheet for monitoring all walk-down reports and material take off. Monitoring all work-packs incoming and outgoing and verify per subsystem closing. Interpret drawings and provide marked-up as per site condition and installation. Secure all documents such as inspection checklist, test reports, calibration certificates, vendor manuals, including testing and commissioning packages.

• Produced and checked Overall Consumer List, Overall Load List and Equipment List for the project.• Execute and supervise site work related on Electrical, Instrumentation and Telecommunication (E&IT).• Review the Project Quality Plans, drawings, project standards and engineering specifications to ensure efficient execution of works.• Help colleague to produce As-built / Red marked drawings as client requirements.• Review the contract, specifications, drawings, industry standards, vendor requirements, and other project agreements on the work to be inspected.• Check all approved design drawings including any approved changes associated with the work to be inspected.• Review material requirements for the materials to be used and obtain material samples for use of inspection activities where appropriate.• Review project procedures and/or the contractor quality plan to determine requirements before starting any activities.• Identify which forms or documents must be completed to document field activities.• Coordinate with client and sub-contractors representative on daily basis to resolve any quality problems or issues. • Secure all documents such as inspection checklist, test reports, calibration certificates, vendor manuals, including testing and commissioning packages.

• Review the contract, specifications, drawings, industry standards, vendor requirements, and other project agreements on the work to be inspected.• Check all approved design drawings including any approved changes associated with the work to be inspected.• Review material requirements for the materials to be used and obtain material samples for use of inspection activities where appropriate.• Review project procedures and/or the contractor quality plan to determine requirements before starting any inspection activities.• Identify which forms or documents must be completed to document field inspection activities.During Inspection: • Check that only approved materials have been used.• Check key dimensional requirements including location, size, clearances, spacing, and other key dimension for the installation.• Perform any required inspection verification testing in the line of electrical and instrument testing and ensure that the testing material is calibrated.• When worker qualification requirement exist, ensure that qualified personnel have performed the work.• Document all inspections per project procedure requirements. If a formal quality control program is implemented on the project, document all inspections performed on the required form.After Performing Inspection: • Immediately advise supervision and/or the contractor of any unacceptable work and the corrective action required to correct the deficiencies.• Follow up on all rejected work after corrective actions have been implemented to ensure that the work is acceptable.• File all inspection records in the project files per procedure requirements.